Heat Transfer in Nature Class 7 Question Answer Science Chapter 7

Start by reviewing these Curiosity Class 7 Solutions and Class 7 Science Chapter 7 Heat Transfer in Nature Question Answer to strengthen your knowledge.

Class 7 Science Curiosity Chapter 7 Question Answer

Science Curiosity Class 7 Chapter 7 Question Answer

Heat Transfer in Nature Class 7 Questions and Answers

Let Us Enhance Our Learning

Question 1.
Choose the correct option in each case.
(i) Your father bought a saucepan made of two different materials, A and B, as shown in fig. The materials A and B have the following properties
Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 1
(a) Both A and B are good conductors of heat
(b) Both A and B are poor conductors of heat
(c) A is a good conductor and B is a poor conductor of heat
(d) A is a poor conductor and B is a good conductor of heat
Answer:
(c) A is a good conductor and B is a poor conductor of heat

(ii) Pins are stuck to a metal strip with wax and a burning candle is kept below the rod, as shown in fig. Which of the following will happen?
Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 2
(a) All the pins will fall almost at the same time
(b) Pins I and II will fall earlier than pins III and IV
(c) Pins I and II will fall later than pins III and IV
(d) Pins II and III will fall almost at the same time
Answer:
(b) Pins I and II will fall earlier than pins III and IV

(iii) A smoke detector is a device that detects smoke and sounds an alarm. Suppose you are fitting a smoke detector in your room.
The most suitable place for this device will be:
(a) Near the floor
(b) In the middle of a wall
(c) On the ceiling
(d) Anywhere in the room
Answer:
(c) On the ceiling

Question 2.
A shopkeeper serves you cold lassi in a tumbler. By chance, the tumbler had a small leak. You were given another tumbler by the shopkeeper to put the leaky tumbler in it. Will this arrangement help to keep the lassi cold for a longer time? Explain.
Answer:
Yes. The air trapped between the two tumblers acts as an insulator (poor conductor of heat). This slows down heat transfer from the surroundings to the cold lassi.

Question 3.
State with reason(s) whether the following statements are True [T] or False [F].
(i) Heat transfer takes place in solids through convection.
Answer:
False; heat transfer takes place in solids through conduction.

Heat Transfer in Nature Class 7 Question Answer Science Chapter 7

(ii) Heat transfer through convection takes place by the actual movement of particles.
Answer:
True

(iii) Areas with clay materials allow more seepage of water than those with sandy materials.
Answer:
False; Sandy materials allow more/ faster seepage than clay due to larger particle spaces.

(iv) The movement of cooler air from land to sea is called land breeze.
Answer:
True

Question 4.
Some ice cubes placed in a dish melt into water after some time. Where do the ice cubes get heat for this transformation?
Answer:
The ice cubes absorb heat from their surroundings, including the air and the surface they are placed on. This heat causes the ice to melt, changing it from a solid state to a liquid state, turning it into water.

Question 5.
A burning incense stick is fixed, pointing downwards. In which direction would the smoke from the incense show the movement of the diagram?
Answer:
The smoke would move upwards.
Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 17
Explanation: Smoke consists of hot gases which are less dense than cool air and rise due to convection.

Question 6.
Two test tubes with water are heated by a candle flame as shown in Fig. Which thermometers (Fig. a or Fig. b) will record a higher temperature? Explain.
Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 3
Answer:
In Fig. (a), the thermometer is placed at the top of the test tube and candle flame heats the bottom of the test tube directly. The water at the bottom gets heated first. As the water heats up, it rises due to convection, carrying heat to the top, where the thermometer is placed. So, the thermometer quickly records a temperature rise.
In Fig. (b), the thermometer is placed at the bottom of the test tube, but the candle flame heats the side of the test tube. The side heating may not be as effective in transferring heat to the bottom where the thermometer is placed. Therefore, the thermometer in Fig. (a) will record a higher temperature.

Question 7.
Why are hollow bricks used to construct the outer walls of houses in hot regions?
Answer:
The air gets trapped in the hollow bricks and air is a poor conductor of heat. This trapped air acts as an insulator and prevent the heat from entering the house, keeping the interior cooler.

Question 8.
Explain how large water bodies prevent extreme temperatures in areas around them.
Answer:
Water heats up and cools down slower than land. During the day, it absorbs heat, keeping coastal areas cooler. At night, it releases heat slowly, keeping coastal areas warmer than inland areas, thus moderating the temperature range. Sea and land breezes also contribute.

Question 9.
Explain how water seeps through the surface of the Earth and gets stored as groundwater.
Answer:
Surface water seeps into the ground through spaces between soil/rock particles (infiltration). It moves downwards until it fills these spaces in saturated layers called aquifers, where it is stored as groundwater. Seepage is faster through porous materials like sand/gravel.

Heat Transfer in Nature Class 7 Question Answer Science Chapter 7

Question 10.
The water cycle helps in the redistribution and replenishment of water on the Earth. Justify the statement.
Answer:
The water cycle helps in the continuous redistribution and replenishment of water on Earth through the movement of water in different stages, such as evaporation, condensation and precipitation. Water from oceans, rivers and lakes evaporates due to the Sun’s heat, forms clouds through condensation, and falls back to Earth as rain or snow through a process called precipitation. The rain refills lakes, rivers and groundwater, ensuring the continuous availability of water on Earth.

Exploratory Projects:

1. Society: Visit a site of water harvesting or a recharge pit. Find out from people how they are constructed and how they work. Prepare a report with illustrations.
Answer:
Here’s a sample report on a site visit to a water harvesting or recharge pit, including explanation, construction method,
Water Harvesting and Recharge Pit Site Visit Report
Name: [Your Name]
Class: [Your Class/Grade]
Date of Visit: [Insert Date]
Location: [Name and address of the site]
Guide/Contact Person: [Name of person interviewed or who guided the visit]

1. Introduction: With the increasing demand for freshwater and the depleting groundwater levels, rainwater harvesting and groundwater recharge have become essential methods for sustainable water management. I visited a Rainwater Harvesting and Recharge Pit site located at [location] to understand how these systems are constructed and how they function.
2. What is a Recharge Pit?
A recharge pit is a simple, cost-effective structure that helps replenish groundwater by allowing rainwater to percolate into the soil.
3. Construction of a Recharge Pit
Materials Used: Bricks or stones, River sand, Gravel and pebbles, Charcoal (for filtration, PVC or GI pipe (for directing rainwater)

Steps in Construction:

  • Digging the Pit: A pit of about 1.5 m × 1.5 m × 2 m is dug, depending on the area’s rainfall and soil type.
  • Layering: The pit is filled with layers of gravel, sand, and charcoal.
  • Bottom: Large stones or gravel (for rapid percolation)
  • Middle: Sand (for filtering finer particles)
  • Top: Charcoal and fine sand (for filtering impurities)
  • Inlet Pipe: Rainwater from rooftops or open areas is directed to the pit through a filter mesh and a pipe.
  • Covering: A perforated concrete slab or mesh is used to cover the pit to prevent debris entry and ensure safety.

4. How It Works?
Answer:
When it rains, water from rooftops or open catchment areas is collected and directed into the recharge pit. The filter layers clean the water, and then it percolates through the soil, reaching the underground water table.

5. Community Feedback
Answer:
I spoke to [Name], a local resident/site manager, who said:
“Since the recharge pit was installed, we’ve seen a noticeable improvement in the groundwater level. Our borewell used to dry up by summer, but now it lasts much longer.”

2. Activity: Tightly wrap a thin paper strip around a metallic rod. Try to burn the paper with a candle while rotating the rod continuously. Does the paper burn? Explain your observations.
Answer:
Aim: To wrap a paper to a rod of metal and burn it.
Procedure: Then burn the paper. Rotate the rod. Put a burning candle below it. Rotate the rod continuously.
Inference: The paper will burn. Smoke is released when the paper is burnt.

3. Activity: Take a sheet of paper. Draw a spiral on it, as shown in [Fig. a]. Cut the paper along the spiral. Suspend the paper as shown in [Fig. b] above a burning candle. Observe what happens.
Provide an explanation for your observation.
Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 4
Answer:
Observation and explanation: A candle is put over the paper. The paper is spiral in shape. The paper is burnt and smoke rises up.
Smoke: It is a mixture containing some hot gases plus minute solid particles. The particles are released when paper burns at all.
Smoke is warmer than surrounding air, this rises upwards then.

Class 7 Curiosity Chapter 7 Question Answer

InText Questions

Question 1.
How does heat get transferred in these materials? (cooking utensils made of metals)
Answer:
The heat is transferred in these materials through a process called conduction. During conduction, the particle that is heated passes the heat to its adjacent particles one after another. The particles remain fixed in their positions.

Question 2.
Is it possble to build houses that remain comfortable inside despite very cold or hot outside weather?
Answer:
Yes, houses in extreme climate use the concept of heat tranfer to stay warm in winter and cool in summers.

Question 3.
How the houses constructed with hollow bricks keep them warm in winters and cool in summers?
Answer:
This happens because the air that gets trapped in the hollow bricks is a poor conductor of heat.

Question 4.
Why is the smoke going up?
Answer:
The smoke is going up because hot air rises. When smoke is produced, it is usually warm or hot. Due to convection, the hot air (and smoke with it) becomes lighter than the surrounding cooler air and rises upwards.

Heat Transfer in Nature Class 7 Question Answer Science Chapter 7

Question 5.
How does heat transfer take place in liquids? Do liquids also rise up when heated, like air?
Answer:
When water is heated in a container, the water at the bottom becomes hot, expands and becomes lighter, causing it to rise. As the warmer water rises, cooler and heavier water moves down to take its place. This process is called convection, and it continues till the entire liquid is heated. Thus, liquids rise when heated, just like air.

Question 6.
I wonder how heat from the fire reaches us?
Answer:
The heat from the fire reaches us through the process of radiation. In this process, heat is transferred by radiating energy to the surroundings. Heat transfer by radiation does not require any medium.

Question 7.
How does water seep through the surface of the Earth?
Answer:
Water seeps through the surface of the Earth by a process called infiltration. From the Earth’s surface the water seeps through the soil containing sand, gravel or clay. Once it seeps, it gets stored in the pore spaces of sediments and the opening in rocks known as aquifers.

Heat Transfer in Nature Question Answer (Activities)

Activity-1: Let us experiment

Aim: To make an experiment for conduction of heat.

Material Required: Metal strip (aluminium or iron), stand, four pins, candles or spirit lamp, wax to attach the pins.

Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 5

Procedure:

  1. Take a metal strip (15 cm long) and attach four pins to it using wax in equal distance(about 2cm apart)
  2. Secure the strip to a stand and label the pins as I, II, III and IV as shown in the figure 1.
  3. Heat the end of the strip away from the stand with a candle or spirit lamp.
  4. Predict the order in which the pin will fall from the strip.
  5. Observe and predict the behaviour of the pins.

Observation:

Table: Falling of pins
Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 6

Pin Falling First Reasons for what you observed
Prediction Observation The first pin (Pin I), closest to the candle flame, falls first, followed by the other pins in order (II, III and IV). The reason for the sequential fall of the pins is the process of heat conduction.
Pin II Falls I
Pin IV Falls II
Pin I Falls III
Pin III Falls IV

Conclusion:

  1. Conduction is the process of heat transfer from the hotter part of a material to the colder part. As the heat travels along the metal strips, it causes the wax holding each pin to melt, leading to the pin falling.
  2. The heat is transferred from the hot end (near the flame) to the colder end through the metal particals vibrating and passing on the energy to their neighbours.
  3. Metals are good conductors of heat, which is why metal utensils are used for cooking.

Heat Transfer in Nature Class 7 Question Answer Science Chapter 7

Precautions:

  1. Activity to be done under supervision of a teacher/an adult person.
  2. Do not touch candle flame.

The upper regions of the Himalayas, such as the Mori block of Uttarkashi in Uttarakhand, experience extremely cold climates and heavy snowfall in winters. To keep houses warm, people build walls with two wooden layers. The space between these wooden layers is filled with cow dung and mud. They both do not allow heat to escape easily. This helps the houses warm and cozy during winter.

Table: List of good or poor conductors of heat
Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 7

S.No. Material Good/Poor conductor of heat
1. Steel Good conductor
2. Wood Poor conductor
3. Plastic Poor conductor
4. Bakelite Poor conductor
5. Aluminium Good conductor

Activity-2: Let us investigate

Aim: To investigate smoke rises up.

Material Required: Two paper cups, thread, wooden stick, candle, match box etc.
Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 8

Procedure:

  1. Take two identical paper cups.
  2. By taking equal lenths of threads, hang these cups in inverted style.
  3. Adjust the position of cups, so that the stick is horizontal.
  4. Place a burning candle under one of the cups.
  5. Record your observation in table.

Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 9

Observation:

Table: Recording observations and probable reasons
Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 10

Observation about the cups Probable reasons for the observation
The cup with the candle underneath rises because the air inside the cup heat up. When air is heated, it expands and takes up more space, making it lighter. This causes the cup to rise.

 

Activity-3: Let us find out

Aim: To find out heat transfer in the liquids.
Material Required: Straw, a 500 ml beaker, water, grain of KMnO4 (potassium permanganate), candle one, stand, a wire net of iron etc.

Procedure:

  1. Fill a 500ml beaker, half with the water.
  2. Using a straw, place a grain of potassium permanganate at the centre of the beaker’s base.
  3. Place one candle at centre of base of beaker. Observe the movement of coloured streak in water.

Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 11

Observations:
The potassium permanganate dissolves, and coloured streaks rise upward in circular pattern, indicating water movement.

Inference:

1. The movement of the coloured streak in the water demonstrates convection, which is how heat tranfer occurs in liquids and gases through the movement of particles.
2. Just like air, water gets heated through convection, where particles move from one place to another carrying heat with them.

Precautions: Perform this activity under supervision of an adult or a teacher.

Activity-4: Let us investigate

Aim: Let us check how land and water get heated or cooled.

Material Required: Two identical bowls, soil, water, two laboratory thermometer.

Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 12

Procedure:

  1. Take two identical bowls.
  2. Fill one bowl halfway with soil and the other halfway with water.
  3. Fix a laboratory thermometer in each bowl, ensuring that the bulbs are immersed in the soil and water respectively.
  4. Place the set-up in sunlight.
  5. Observe the rise in temperature of the soil and water over a period of time.

Observation Table

Table: Temperature of soil and water when heated
Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 13

S.No. Time (min) Temperature of soil (°C) Temperature of water (°C)
1. 0 25 25
2. 5 28 26
3. 10 31 27
4. 15 34 28
5. 20 36 28
6. 25 38 29

Observation:
After 20 minutes, you will find that the temperature of the soil rises more than that of the water. This indicates that the soil heats up faster than water.

Cooling Experiment:

  • After letting the soil and water heat up, bring the set-up indoor and allow it to cool for 20 minutes.
  • Observe the cooling rates of the soil and water.

Conclusion: Soil heats and cools up faster than water due to differences in specific heat capacity.

Precaution:

  1. This activity should be carried out on a clear, sunny day under the supervision of a teacher or an adult.
  2. Carefully fix the thermometers in bowls, don’t touch the bottom or sides of the bowls.

In Himalayan region, a traditional room heater called bukhari is used to keep rooms warm in winter. It is an iron stove where wood or charcoal is burned. A long pipe attached at the top acts as a chimney to release smoke.

Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 14

The flat top of the bukhari can also be used for cooking by placing utensils on it. When the bukhari is used, all three types of heat tranfer- conduction, convection and radiation work together to warm the room and cook food.

Activity-5: Let us investigate

Aim: To investigate seepage of water beneath the earth.

Material Required: Three plastic bottles, clay, sand, gravel, water etc.

Procedure:

  1. Take three transparent, used plastic bottles of 1 L capacity.
  2. Cut them in the middle and make a small hole in the cap of each bottle.
  3. Place three identical beakers below each bottle.
  4. Add 200 mL of water to each bottle and predict the amount of water flowing out of each bottle.
  5. Collect the water that flows through each bottle for 10 minutes.
  6. Compare the amount of water that comes through each bottle.

Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 15

Observations:

Table: Seepage of water
Heat Transfer in Nature Class 7 Question Answer Science Chapter 7 16

Bottles filled with

Bottle 1 (Clay)

Prediction Observations
Seepage of water (very slow/slow/fast) Seepage of water (very slow/slow/fast)
Bottle 2 (Sand) slow very slow
Bottle 3 (Gravel) very slow slow
Bottles filled with fast fast

Conclusion:
It is observed that water flows fastest through gravel, slowest through sand and very slow through clay. This is due to the differences in the particle sizes and the spaces between them.

Inference:
This explains that water seeps through materials based on particular size and pore spaces.